FDJ-120风动手持切开锯是我公司关于高危，安全系数请求特别高的作业环境，如化工.治炼厂.天然气挖掘.高危潮湿的地道，水下及狭窄的空间作业，尤其是高瓦斯防爆矿井。山西万泽锦达矿山机械设备有限公司自立研制的新式多用途风动手持切开东西。它使用中国台湾进口气动马达作为动力输出，使用压缩空气作为动力源，不必电源。风动手持切开锯不光整机分量轻，操作简略，携带方便零火花，进步作业效益。本商品安全可靠是高危职业的抱负气动切开东西。

FDJ-120风动切割锯技术参数:

1：适用资料:不锈钢.铝，铜.铬合金，镍基合金，玻璃，纤维，木材，塑料，钢丝绳等。

2：切开规模：120mm*120mm圆型资料，220mm*120mm方型资料。

3：作业压力：0.3—0.8Mpa

4：外型尺度：650*210*270

FDJ-120风动切割锯长处

1：90°直切,45°斜切,立式切开一体机。

2：运转速度只要砂轮机的1/60,安全无火花。

3：切缝窄0.5mm,切开外表平整，精度高，无挂渣，无脱碳。

4：锯条使用寿命长，单位切开成本低，一根锯条使用寿命等同于50-80片砂轮切开片，较电能锯节能60%

FDJ-120风动切割锯使用方法：

1、了解所需切开的资料，如有必要能够经过下降空气压力来下降锯片的滚动速度。矿用锚杆锚索切割锯宁夏 优质

2、保证结实固定了所需切开的资料，避免其移动。

3、气动空气马达时，用手指按压阀杆，然后开端切开。

4、用锯的分量来操控切开压力。关于较软的资料来说，这么的分量已经满足。过多的压力会下降锯片的速度。关于较硬的资料，能够经过加压的方法来下降锯片的滚动速度。切开是坚持锯垂直。锯片的任何歪曲或倾斜都也许下降其使用寿命。（留意：避开切开后也许坠落的碎片。切开行将完结时，切勿使锯碰到您的身体、工件或邻近的其它人员。）

5、封闭空气马达时，开释阀杆。

6、下次切开开端前，锯片有必要坚持运动状况。气动锯时，锯片不能触摸任何外表。

7、断开空气软管时，封闭空气软管阀。断开前，先翻开空气阀给软管减压。

8、替换锯片前，有必要断开空气软管，并推进阀杆以开释掉马达内的压力。

9、顺时针滚动调整手柄以便开释锯片导杆上的张力。然后开释侧面板的锁以便翻开侧面板。然后从驱动轮上取下锯片并将其从锯带导杆上松开。

FDJ-120 pneumatic hand cut saw is my company on risk, safety factor request especially high operating environment, such as chemical refinery. Natural gas mining. High wet tunnels, underwater and narrow space operations, especially in high gas coal mine explosion. The new multi purpose pneumatic Shanxi million Zejin of mining machinery and equipment limited company of independent research and hand cut things. It uses the imported pneumatic motor of Taiwan as power output, uses compressed air as power source, and does not have to power. The pneumatic handheld cut saw is not light, the operation is simple, it is convenient to carry zero spark, and improve the efficiency of operation. This product is safe and reliable is a high-risk career aspirations pneumatic incision.
FDJ-120 pneumatic cutting saw technical parameters:
1: applicable materials: stainless steel, aluminum, copper, chromium alloy, nickel base alloy, glass, fiber, wood, plastic, wire rope and so on.
2: incision size: 120mm*120mm circular data, 220mm*120mm square data.
3: job pressure: 0.3 - 0.8Mpa
4: the external scale: 650*210*270
FDJ-120 wind cutting saw length
45 degrees 1:90 degrees straight, oblique, vertical incision machine.
2: the speed of operation is as long as the 1/60 of the sand turbine, safe and free of spark.
3: the slit is narrow 0.5mm, the incision is smooth, the precision is high, no slag, no decarburization.
4: the long service life of the saw blade, and a unit cost is low and the service life of the saw blade and the equivalent of 50-80 wheel cut open, a power saw 60% energy saving
FDJ-120 pneumatic cutting saw use method:
1. Understand the material that needs to be cut, such as the reduction of air pressure to reduce the rolling speed of the saw blade. Cutting and sawing Ningxia high quality with mining bolt and anchor cable
2, ensure the sturdy fixation of the required open data to avoid its movement.
3. When pneumatic air motor, press the stem with the finger, and begin to cut.
4, use the component of the saw to control the cut pressure. For the softer data, this component has been satisfied. Too much pressure will reduce the speed of the saw blade. With more hard data, the rolling speed of the saw blade can be reduced by a pressurized method. The incision is to stick to the saw vertical. Any distortion or tilt of the saw may decrease its service life. (notice: avoid fragments that may fall after a cut. Do not make the saw touch your body, the workpiece, or the other people in the neighborhood when the cut will be finished.
5. When the air motor is closed, the stem is released.
6. Before the next opening, it is necessary to adhere to the movement of the saw blade. When a pneumatic saw, a saw can't touch any appearance.
7. When the air hose is disconnected, the air hose valve is closed. Before disconnecting, open the air valve and decompress the hose.
8. Before replacing the saw, it is necessary to disconnect the air hose and push the stem to release the pressure of Madane.
9, adjust the handle clockwise to release the tension on the sawing guide rod. Then release the lock of the side panel so as to open the side panel. Then remove the blade from the drive wheel and release it from the sawing guide rod.