电容器纸工频电压击穿测试仪

型号分：10KV-200KV

适用范围及功能
主要适用于固体绝缘材料（如：塑料、橡胶、层压材料、薄膜、树脂、云母、陶瓷、玻璃、绝缘漆等绝缘材料及绝缘件）在工频电压或直流电压下击穿强度和耐电压的测试。
本仪器由电脑控制，是我公司自主研发的全新第二代介电击穿检测仪器，本仪器由数字集成电路系统与软件控制系统两大部分构成，使升压速率真正做到匀速、准确，并能够准确测出漏电电流的数据。可实时绘制试验曲线，显示试验数据，判断准确，并可保存，分析，打印试验数据。本系统能够自动判别试样击穿并采集击穿电压数据及泄露电流，同时能够在击穿的瞬间电压迅速降低自动归零。软件系统操作方便，性能稳定，安全可靠。

技术要求：
01、输入电压： 交流 220 V
02、输出电压： 交流 0--50 KV ;
               直流 0--70 KV ;（同类产品做到50kv）
03、电器容量： 3KVA
04、高压分级： 0--50KV 全程可调（采用高精度电压采样器件，取消了同类厂家由于电压采样精度不够必须采用高压分级的方式）
05、升压速率：
100 V/S 
200 V/S
 500 V/S
 1000 V/S
 2500 V/S
 3000 V/S （此项满足标准里面极快速升压试验要求）
    备注：注：本产品采用的直流伺服电机加载减速机构，保证了标准里面关于极慢速试验和极快速试验的要求，（一般厂家为皮带轮机构，误差较大）保证用户可以自由选择升压速率，是目前同类产品中*满足国标对于升压速率要求的测试设备。可以根据用户需求设定不同的升压速率

06、试验方式：
           直流试验：1、匀速升压 2、阶梯升压 3、耐压试验
           交流试验：1、匀速升压 2、阶梯升压 3、耐压试验
 
注：根据不同行业的标准，我们可以根据用户的要求，依据贵行业标准，为您定制行业标准所需的特殊测试功能。
07、电压试验精度： ≤ 1％
 08、电极规格：1、片材电极 ￠25mm  两个   片材电极 ￠75mm一只
                 2、管用电极          两个 、一套。
09、过电流保护装置应有足够灵敏度以保证试样击穿时在0.05S内切断电源。
10、本仪器采用*的无触点原件匀速调压方式，淘汰同类产品中机械传动升压方式。
11、一次试验可以做5个试样。备注:（同类产品一次试验只能做一个试样）
12、耐压时间设定：0-6小时（可通过软件连续设定）
 

安全保护：
 本仪器具有比较完善的安全防护措施：
本试验仪器电路保护控制：
九级安全防护措施： 备注:一般厂家为5级
（1） 超压保护
（2）试验过流保护
（3）试验短路保护
（4）安全门开启保护
（5）软件误操作保护
（6）零电压复位保护（避免一般厂家急停断电不复位二次试验继续升压的危险）
（7）试验结束放电保护

满足标准：GB/T 1408-2006 绝缘材料电气强度试验方法
          GB/T1695-2005 硫化橡胶工频电压击穿强度和耐电压强度试验
          GB/T3333 电缆纸工频电压击穿试验方法
          HG/T 3330绝缘漆漆膜击穿强度测定法
          GB12656 电容器纸工频电压击穿试验方法
          ASTM D149 固体电绝缘材料在工业电源频率下的介电击穿电压和介电强度的试验方法.

北京北广精仪仪器设备有限公司*产品：
（橡胶塑料电性能系列）电压击穿试验仪，电气强度测试仪，介电击穿强度测定仪，电子*试验机，体积电阻率表面电阻率测试仪，介电常数及介质损耗测试仪，漏电起痕试验仪，水平垂直燃烧仪，橡胶低温脆性冲击试验仪，熔融指数仪，熔体流动速率测定仪，塑料热变形维卡软化点温度测定仪，滑动摩擦磨损试验机，耐电弧试验机，马丁耐热试验仪，建材可燃试验仪，球压痕硬度计，简支梁试验机，电热毯动负载试验机，*试验机，冲片机，哑铃制样机，落锤冲击、落镖冲击，落球冲击试验机，指数仪等
（海绵泡沫系列）海绵泡沫压陷硬度测定仪，落球回弹试验机，海绵切割机，海绵拉伸强度试验机，和疲劳压陷试验机，压缩变形试验机，撕裂强度，回弹率等。

Breakdown voltage tester - Computer Control

Model points: 10KV-200KV

Meet the standards: GB / T 1408-2006 Test method for insulating materials Electrical strength
          GB/T1695-2005 vulcanized rubber frequency voltage breakdown strength and dielectric strength test
          GB/T3333 cable paper frequency voltage breakdown test methods
          HG / T 3330 varnish film breakdown strength determination
          GB12656 capacitor paper frequency voltage breakdown test methods
          ASTM D149 Solid Electrical Insulating Materials at Commercial Power frequency dielectric breakdown voltage and dielectric strength test methods.

First, the scope and functions
Primarily applicable to solid insulating materials （such as: plastic, rubber, laminates, films, resins, mica, ceramic, glass, insulating paint and other insulating materials and insulating member） in the frequency voltage or DC voltage and resistance to voltage breakdown strength tests.
The instrument is controlled by computer, is my company developed a new second-generation dielectric breakdown testing instruments, the instrument consists of digital integrated systems and software control system composed of two parts, the boost rate truly uniform, accurate, and the ability to accuray measure the leakage current data. Real-time rendering test curve shows the test data to determine accuray, and save, analyze, print test data. The system can automatically determine and collect the sample breakdown breakdown voltage and leakage current data, and be able to quickly lower the breakdown voltage of the instant auto zero. Software system is easy to operate, stable performance, safe and reliable.

Second, the software features:
    01, the software platform: WINDOWS windows operating platform, intuitive interface, easy to operate
02, the curve shows: In the course of the experiment can dynamically display test curves
03, data export: You can import EXCEL spreadsheet on the test results
04, test report: report name can be artificially set, and lab reports for printing
05, Test Method: Test according to requirements of the DC and AC tests the flexibility to choose
06, Test Method: You can choose according to their own needs breakdown voltage, pressure test, the gradient test
07, parameter setting: according to different test methods and test methods needed flexibility to set different parameters
08, the sample settings: Standard samples for different parameters set flexibly
09, Personnel Management: Set the user name and password, different operators logged different tests, independently of each other
10, the standard options: with different standards, according to the needs of their own choice
11, continuous operation: Continuous operation test can be directly in the software end of the test, a second test

Third, the technical requirements:

01, the input voltage: AC 220 V
02, the output voltage: AC 0 - 50 KV;
               DC 0 - 70 KV; （similar products do 50kv）
03, electrical capacity: 3KVA
04, high grade: 0 - 50KV full adjustable （using high-precision voltage sampling devices similar manufacturers canceled due to the voltage must be high enough sampling accuracy hierarchical manner）
05, the boost rate:
100 V / S
200 V / S
 500 V / S
 1000 V / S
 2500 V / S
 3000 V / S （The latest standards which meet the test requirements very quickly boost）
    Note: Note: This product uses the most advanced DC servo motor load reduction mechanism to ensure that the latest standard test on the inside very slow and very fast testing of the latest requirements （general manufacturers of pulley mechanism, large errors） to ensure that users can freely select the boost rate, is currently the only product in its class to meet the national standard for the boost rate required test equipment. Set different according to user needs the boost rate

06, Test Method:
           DC test: 1, uniform step two, step step 3, the pressure test
           AC test: 1, uniform step two, step step 3, the pressure test
 
Note: Depending on the industry standard, we can according to user requirements, according to the industry standards, industry standards required for your custom special test function.
07, voltage test accuracy: ≤ 1%
 08, the electrode Specification: 1, sheet electrode ￠ 25mm ￠ 75mm two sheet electrodes a
                 2, effective electrode two, one set.
09, over-current protection device shall have sufficient sensitivity to ensure that the sample breakdown in 0.05S cut off the power within.
10, the instrument uses advanced non-contact voltage regulator original uniform way out similar products in the mechanical transmission boost mode.
11, a test can be done five specimens. Note: （a test similar products can only do one sample）
12, pressure time setting :0-6 hours （continuous setting via software）

Fourth, security protection:
 The instrument has a relatively complete safety precautions:
This test instrument control circuit protection:
Nine security measures: Note: Average manufacturers to 5
（1） overpressure protection
（2） Test Overcurrent
（3） Short-circuit protection test
（4） protect the safety door open
（5） Software misuse protection
（6） zero voltage reset protection （emergency power off to avoid general manufacturers continue to boost two trials is not reset danger）
（7） end of the test-discharge protection
（8） separate protective earthing
（9） end of the trial discharge protection （exclusive of the most secure and effective resin-firing rod manufacturers to avoid a general way the traditional discharge and electromagnetic interference discharge residue discharge phenomenon）

Fifth, test methods
1, insulation breakdown or sample the air pressure test
2, insulation breakdown or sample immersion oil pressure test
1, insulation breakdown or ladder sample air pressure test
2, insulation ladder sample immersion oil breakdown or pressure test
Note: According to user requirements, other test methods can be customized

Beijing North Canton Precision Instrument Co., Ltd. Hot products:
（Plastic and Electric Performance Series） voltage breakdown tester, electrical strength tester, dielectric breakdown strength tester, electronic universal testing machine, surface resistivity tester volume resistivity, dielectric constant and dielectric loss tester, leakage Tracking tester, horizontal and vertical burning tester, low temperature brittleness rubber impact tester, melt index tester, melt flow rate tester, plastic heat distortion temperature Vicat softening point tester, sliding friction and wear testing machine, arc resistance testing machine, Martin heat tester, combustible materials tester, ball indentation hardness tester, Charpy test machine, electric blankets dynamic load testing machine, universal testing machine, punching machine, dumbbell system prototype, drop hammer, dart impact, Falling ball impact test machine, instrument, such as index
（Sponge foam series） foam sponge hardness indentation tester, ball rebound test machine, foam cutting machine, foam tensile strength testing machine, pressure depression and fatigue testing machine, compression testing machine, tear strength, resilience rate .

Service and Warranty:
Over the years, our company has been specializing in the production of electrical test equipment, through research, exploration, summed up a complete product service support system, to provide users with high-quality and timely pre-sales, after-sales service
To create brand, enhance their visibility and establish a corporate image, our spirit of "all the pursuit of quality, customer satisfaction for the purpose of" spirit, "the most preferential prices, the most attentive service, the most reliable product quality" principle You solemn promise:

A commitment to product quality:
1, I need to provide to ensure that the original production equipment, and factory data accessories complete. In order to maintain the normal operation of the contract and maintenance of equipment, I guarantee to provide technical information and drawings are complete, clear and correct.
2, product manufacturing and testing are quality records and test data.
3, the product performance testing, we sincerely invite users to visit the product of the whole process, all performance checks, was confirmed to be eligible after the boxed product shipped.

Second, the product price promise:
1, in order to ensure high reliability and advanced systems were chosen selection of quality brand-name domestic or international.
2, in the same competitive conditions, our company not to reduce product performance, change the product on the basis of the cost of parts, in good faith in the most favorable price to your side.

Three: installation, commissioning and acceptance of commitments:
1, to assist with the installation, responsible for equipment transport and commissioning.
2, the device according to order technical annex for acceptance. Final acceptance for the purchaser, the user-supplied samples to test and provide test reports.
3, installation and commissioning while operating the instrument off-site training of operators free 2-3, the operator should be selected by the demand side of the long-term stability of staff training to the basic principles of the equipment, software, use, operation, maintenance Matters understanding and application of the device that are able to operate independently of the sample detection, analysis, and can carry out basic maintenance.

Fourth, warranty:
1, the device year warranty and lifetime service within one year of non-human damaged parts replaced free of charge during the warranty period the user received an invitation, at the latest within a response time of 2 hours, after the failure with user confirmation, I will 48 hours to send engineers to arrive at the scene for a free service, as soon as possible to identify the fault location and cause of the malfunction, failure to promptly report the reasons for users and exclusion methods.
2, man-made damaged parts during the warranty period by purchasing （processing） prices charged replacement.
3, the warranty period to continue to provide users with high-quality technical services, the user received within 3 days after repair invited to send engineers to reach users on-site repair. And enjoy the preferential treatment of purchased parts.
4, the sensor and the whole circuit overload overpressure damage is not covered under warranty.