1. Product introduction: It is a testing instrument that can be used as a special physical performance testing instrument for the paint, coating, and ink industries. The whole machine is compact in st......
详细介绍
一、产品简介：是检测仪器，可作颜料、涂料、油墨行业专用的物理性能检验仪器。整机结构紧凑，外观简洁，转数和负荷变换方便，下班盘装拆简便。采用液晶屏显示，参数设置方便。平磨仪是**标准GB5211.19《着我颜料相对着色力和冲淡的测定目视比较法》中的仪器。 1. Product introduction: It is a testing instrument that can be used as a special physical performance testing instrument for the paint, coating, and ink industries. The whole machine is compact in structure, simple in appearance, convenient to change the number of revolutions and load, and easy to install and disassemble off-duty trays. It adopts LCD screen to display, convenient parameter setting. The flat grinder is an instrument in the ** standard GB5211.19 "The Visual Comparison Method for the Determination of the Relative Tinting Strength and Dilutedness of Paints".
二、技术参数： ★磨盘直径：240mm ★荷 载： 43 kg 64kg 100kg ★砝码重量： 1.75kg 3.5kg 6.42kg ★电源电压： 220VAC 50HZ ★ 玻璃盘转速:75 转/分±5转/分 ★设定圈数显示范围：1~9999 ★运转圈数显示范围：0~9999 ★累计次数显示范围：0~9999 ★外形尺寸： 580*360*480mm ★重量：约80kg ★电动机功率：0.75kw 2. Technical parameters: ★Diameter of Grinding Disc: 240mm ★Load: 43 kg 64kg 100kg ★The weight of the weight: 1.75kg 3.5kg 6.42kg ★Power supply voltage: 220VAC 50HZ ★ Rotation speed of glass plate: 75 rpm ± 5 rpm ★Display range of setting laps: 1~9999 ★Display range of the number of revolutions: 0~9999 ★Display range of accumulated times: 0~9999 ★Dimensions: 580*360*480mm ★Weight: about 80kg ★Motor power: 0.75kw
三、操作步骤： ★将定量的试样和调和剂放在下磨盘上，用调刀调和成浆，然后将调和好的浆移到下磨盘的**位置，并放下上磨盘，使定位轴芯与定位块扣上，再将偏心手柄向下板，挂上所需砝码。 ★合上控制器的电源开关时，蜂鸣器发出“滴”的一声。 ★液晶屏显示开机画面： ★按键盘上的“设定”键进入设定圈数的万位，此时万位在闪烁，按下“▲”键万位数值加1，按下“?”键循环移一位。按下“确定”键确定设定圈数，进入功能操作。但设定圈数不为0，否则显示“输入设定圈数”，重新设置。在设定圈数期间不能按下功能键，否则显示设定圈数，重新设置。若“确定”键按下发现设定圈数有误可按下“设定”键重新设置。若确定设定圈数正确，按下“运转”键，此时电动机开始运行。每转动一圈。“运转圈数”自动累计加1。当运转圈数和设定圈数相同时，电动机自动停止运转，此时蜂鸣器发出“嘀嘀嘀”的报警声，“累计次数”自动加1。此时扳动偏心手柄，把磨盘上、下分离，将定位手柄往外拉，同时向上推起，打开上磨盘，观察试样。 ★若按照上一次设定的圈数再运转一次，**直接按“运转”按键；如要在中途停机，则可按“停止”按键。若“清零A”则“运转圈数A”计数器会自动清零；若“清零B”则“累计次数B”计数器会自动清零，于此同时会发出“嘀”的一声。要再继续工作只需按“运转”按键，机器将继续运转，直到运转到设定的圈数为止。 ★若机器要长时间运转，则应停止计数器计数。此时“运转圈数”会显示“STOP”；假如不想长时间运转，**再按一次“停止计数”按键，机器**恢复到原来计数状态。 ★若机械运转过程中按“设定”键，整机将停止运行。同时“设定圈数”万位闪烁、“清零A”和“清零B”的数值。 ★如需水冷，则接通上磨盘的水嘴。 3. Operation steps: ★Put the quantitative sample and blending agent on the lower grinding disc, use the knife to adjust the pulp, then move the blended pulp to the ** position of the lower grinding disc, and put down the upper grinding disc, so that the positioning shaft core and the positioning block are buckled , Then move the eccentric handle to the lower plate, and hang the required weights. ★When closing the power switch of the controller, the buzzer will make a beep. ★The LCD screen displays the boot screen: ★Press the "Set" button on the keyboard to enter the ten-thousａnd digit of the set number of laps. At this time, the ten-thousａnd digit is flashing. Press the "▲" key to increase the ten-thousａnd digit value by 1, and press the "?" Press the "OK" key to confirm the set number of laps and enter the function operation. But the set number of laps is not 0, otherwise it will display "input set number of laps" and reset. The function key cannot be pressed during the setting of the number of laps, otherwise the set number of laps will be displayed and reset. If you find that the number of laps is wrong when you press the "OK" button, you can press the "Set" button to reset it. If you are sure that the set number of laps is correct, press the "Run" key, and the motor will start to run at this time. Every turn. The "number of revolutions" automatically accumulates by 1. When the number of running laps is the same as the set number of laps, the motor will automatically stop running. At this time, the buzzer emits a "di di di" alarm sound, and the "accumulated number of times" automatically increases by 1. At this time, pull the eccentric handle to separate the upper and lower grinding discs, pull the positioning handle outwards and push up at the same time, open the upper grinding disc, and observe the sample. ★If you run again according to the number of laps set last time,** directly press the "Run" button; if you want to stop in the middle, you can press the "Stop" button. If "Clear A", the "Running Number A" counter will be automatically cleared; if "Clear B", the "Accumulative Times B" counter will be automatically cleared, and a beep will be emitted at the same time. To continue working, just press the "Run" button, and the machine will continue to run until it reaches the set number of laps. ★If the machine needs to run for a long time, the counter should be stopped. At this time, "Running laps" will display "STOP"; if you don't want to run for a long time, **press the "stop counting" button again, and the machine** will return to the original counting state. ★If the "set" button is pressed during machine operation, the whole machine will stop running. At the same time, the 10,000 digits of "Set the number of laps" flash, and the values of "Zero A" and "Zero B" are flashing. ★If water cooling is needed, connect the water nozzle of the upper grinding disc.
