品牌
经销商厂商性质
上海市所在地
威格士PVB系列轴向柱塞泵全新**大量库存
PVH131L12AF30B252000001AJ200010A PVH131C-LBF-12D-10-C25V-31
PVH131L12AF30B252000001AJ100010A PVH131C-LBF-12S-10-C25V-31
PVH131L12AF30B252000001AY100010A PVH131C-LBF-12S-10-C25V-31-114
PVH131L12AF30B502000001AJ1AA010A PVH131C-LBF-12S-11-C31V-31
PVH131L02AF30B162000001AJ1AA010A PVH131C-LBF-2S-11-C16V-31
PVH131L02AF30B252000001AJ1AA010A PVH131C-LBF-2S-11-C25V-31
PVH131L03AF30B252000001AJ1AA010A PVH131C-LBF-3S-11-C25V-31
PVH131L12AF30B252000001AM2AA010A PVH131C-LCF-12D-11-C25V-31
PVH131L12AF30B482000001AA1AA010A PVH131C-LCF-12S-11-C275V-31-CD-114
PVH131L16AF30B252000001AM100010A PVH131C-LCF-16S-10-C25V-31
PVH131L03AF30B252000001AM1AA010A PVH131C-LCF-3S-11-C25V-31
PVH131L12AF30A250000001002AA010A PVH131C-LF-12D-11-C25-31
PVH131L12AF30B25200000100100010A PVH131C-LF-12S-10-C25V-31
PVH131L12AF30B252000001001AM010A PVH131C-LF-12S-10-C25V-31-118
PVH131L33AF30B252000001002AA010A PVH131C-LF-13D-11-C25V-31-259
PVH131L13AF30A25000000100100010A PVH131C-LF-13S-10-C25-31
PVH131L13AF30B25200000100100010A PVH131C-LF-13S-10-C25V-31
PVH131L13AF30B192000AK1001AA010A PVH131C-LF-13S-11-C19V-31-188
PVH131L13AF30B252000001001AA010A PVH131C-LF-13S-11-C25V-31
PVH131L29AF30B25200000100100010A PVH131C-LF-29S-10-C25V-31-046
PVH131L29AF30B25340000100100010A PVH131C-LF-29S-10-C25V34-31-CD-046
PVH131L02AF30B21200000100200010A PVH131C-LF-2D-10-C21V-31-046
PVH131L02AF30B252000001002AA010A PVH131C-LF-2D-11-C25V-31
PVH131L02AF30B252000001008AA010A PVH131C-LF-2D-11-C25V-31-214
PVH131L02AF30B25200000100100010A PVH131C-LF-2S-10-C25V-31-046
PVH131L02AF30B252000AL1001AP010A PVH131C-LF-2S-10-C25V-31-208
PVH131L02AF30B192000AA1001AA010A PVH131C-LF-2S-11-C19VB-31-CD
PVH131L02AF30B252000001001AA010A PVH131C-LF-2S-11-C25V-31-046
威格士PVB系列轴向柱塞泵全新**大量库存
| 故障 | 产生原因 | 排除方法 |
| 泵不供油或供油不足 | 泵不转或转速低 | 确认油泵与原动机连接正常 |
| 转向不对 | 更改原动机旋向或更换成相反旋向的齿轮泵加油至规定位置 | |
| 进出油口接反 | 按标牌所示进行正确连接 | |
| 吸油管道或过滤器堵塞 | 检查管路清洗或更换滤油器 | |
| 吸入管道漏气 | 检查吸入管道并密封、紧固 | |
| 泵盖螺钉松动 | 拧紧螺钉 | |
| 系统中有泄漏 | 检查系统修补泄漏点 | |
| 油液粘度过高或过低 | 使用*油液 | |
| 油温过低或过高 | 预热或冷却并使用*油液 | |
| 压力上不去 | 溢流阀调定压力太低或已失灵 | 检查调整溢流阀压力或更换溢流阀 |
| 吸入空气 | 检查吸油管路排除吸气现象 | |
| 系统中有泄漏 | 检查系统修补泄漏点 | |
| 油液中有气泡 | 补充油液或把回油口浸入油下 | |
| 漏油 | 油液粘度太低 | 使用*油液 |
| 密封件老化 | 到维修站或生产厂修理 | |
| 连接螺钉或接头松动 | 紧固螺钉或管接头 | |
| 噪声大或振动大 | 吸油管路或滤油器堵塞 | 检查管路清洗或更换滤油器 |
| 吸油高度过大 | 降低吸油高度 | |
| 油液粘度过大 | 使用*油液 | |
| 吸入空气 | 检查吸油管路排除吸气现象 | |
| 泵轴和原动机不同轴 | 重新安装使用同轴度小于0.05 | |
| 油液中有气泡 | 补充油液或把回油口浸入油下 | |
| 泵转速过高 | 降低转速 | |
| 泵压力过高 | 降低压力 | |
| 严重发热 | 安装间隙过小 | 检查修复 |
| 油箱容积太小 | 增大油箱容积 |
