智能制造网

一，产品简介：

用来检测水泥浆、腻子、石膏、灰浆以及细混凝土等A大颗粒物直径为2毫米的物质建筑材料的施工性能。
First, the product introduction:
It is used to test the construction performance of material building materials with a maximum particle diameter of 2 mm, such as cement slurry, putty, gypsum, mortar and fine concrete.

二，得出如下数据：

♦ 流变曲线和流变参数
♦ 温度与施工性能的关系
♦ 在一定搅拌速率下固化行为与时间的关系
♦ 混凝土添加剂和无机掺合剂对施工性能的影响。
econd, the following data is obtained:
♦ Rheological curve and rheological parameters
♦ Relationship between temperature and construction performance
♦ Relationship between curing behavior and time at a certain stirring rate
♦ Influence of concrete additives and inorganic admixtures on construction performance.

三、构造及原理
♦ 由高精度的马达驱动。每一个转动的分辨率为200步。它可以在两个方向上以0.001到400 转/分钟转动并记录下流变曲线和数据点。测量A大扭矩为±250Nmm，通过一个特制的传声器测量。
♦ 测量系统由一个固定的探针组成，探针同心地固定在一个可以选择的圆柱状样品容器里。当样品在探针周围流动时，切力产生的扭矩被连续地记录下来。探针固定在测量器的顶部，自动运转和停止，这样便可以方便地填充、倒空和清洗样品容器。样品容器固定在转动驱动轴上。
♦ 温度可以由一个位于测量探针下的传感器测量。
♦ 扭矩、时间和温度在测量过程中以图的形式实时显示。

Third, structure and principle
♦ Driven by a high precision motor. The resolution of each rotation is 200 steps. It can rotate and record rheological curves and data points at 0.001 to 400 rpm in both directions. The maximum torque measured is ±250 Nmm and is measured by a special microphone.
♦ The measurement system consists of a fixed probe that is concentrically fixed in a cylindrical sample container of choice. When the sample flows around the probe, the torque generated by the shear force is continuously recorded. The probe is attached to the top of the meter and automatically runs and stops so that the sample container can be easily filled, emptied and cleaned. The sample container is attached to the rotary drive shaft.
♦ The temperature can be measured by a sensor located under the measuring probe.
♦ Torque, time and temperature are displayed in real time in the form of graphs during the measurement process.

三，特点
1， 用于工业环境的耐用的工具；
2，质量控制、研究和开发；
3， 方便使用；
4， 预先定义测试步骤并自动运行。这些步骤可以是标准化的，也可以根据要求来设定；
可测量不均匀的颗粒，zui大直径为2毫米。它们能通过专用探针进行有效的分离。

Third, the characteristics
1，Durable tools for industrial environments;
2，Quality control, research and development;
3， Easy to use;
4， Pre-define the test steps and run them automatically. These steps can be standardized or set as required;
It can measure uneven particles, and the large diameter of zui is 2 mm. They can be effectively separated by dedicated probes.

四、仪器配置